Detex V50 EE Uživatelský manuál

FOR SPECIAL LOCKING ARRANGEMENT:THIS PRODUCT MUST BE CONNECTED INTO A FIRE ALARM SYSTEM PER NFPA CODE OR OTHERREGULATIONS SO THAT, IN THE EVENT OF FIR

104832 Page 10Slide and mount endcapto endcap bracket with two1/4-20x1" PPH machine screwsor #14 self-drilling screws.DO NOT OVERTIGHTENFor 1/4-2

104832 Page 11Right Hand Reverse (RHR)NOTE:If link is not in uppermost position on the centerlift, carefully remove "E" clips and reposition

104832 Page 12TOP LATCH TESTING AND ADJUSTMENT1. Close the door. The holdback lever should engage the backside of the strike, allowing the latchbolt t

104832 Page 13Thread 1/4-20 X 1"hexbolt into rod aMINIMUM of 1/2"5/8" BOLTENGAGEMENTFinishedFloorNOTE: IF TRO DEVICE, SKIP THIS PAGE AN

104832 Page 14Rotate bolt for minorrod height adjustment.Lock bolt headfirmly in placein carriage withplate, starwasherand screwFIG. 13With Door close

104832 Page 15FIRE RATED TOP ROD ONLY (TRO) DOORS3/4" Dia. Min.1-1/4" Deep min.Retaining ClipPopperCap Plug12"12"9/16" Dia. M

104832 Page 16Place ECL-395-Xsign on doorSpace 1 rod guide equidistant betweencentercase and latch assemblies(7 foot and 8 foot doors). Use 2 rodguide

104832 Page 179V AlkalineBatteryRED/BLK WIRESTO 24 VOLT(PC BOARD ASSEMBLY INSIDEDELAYED EGRESS DEVICE)To disable the low-batteryindication, slide the

104832 Page 181 2POWER REQUIREMENT:.5 AMPS @ 24 VDCFactoryinstalledjumperThe key cylinder arming switch must be set to "OFF". To prevent th

104832 Page 19RISER DIAGRAMDETEX FILTERED AND REGULATED POWER SUPPLYWITH FIRE ALARM SYSTEM LOOP 24 VDC @1 AMP MINDETEX REQUIRES THE POWER SUPPLY BE LO

P/N: 101825-1P/N: ECL-395-XDoor SignDETEXDetex Power Supply Catalog No: 90-800(80-800 Battery back-up power supplyavailable)* Notes: 1. Parts listed

104832 Page 204Note: For high traffic areas an electric through-wire hinge or power transferis recommended.Value Series FlexConduit/End Cap KitCatalog

104832 Page 21NORMAL OPERATIONNUISANCE DELAYEXITING UNDER ALARMBATTERY BACKUP FOR ALARMTurn Key CW To DisarmRed LED while alarmingARMING AND AUTHORIZE

104832 Page 22TROUBLESHOOTINGFor further assistance, contact Detex Technical Support 1-800-729-3839Probable CauseTurn key clockwise to OFF position.Co

104832 Page 23Catalog No: SN2 Stainless Steel BHMA 630 FinishCatalog No: SN2 Brushed Brass BHMA 606 FinishCatalog No: SN2 Brushed Chrome BHMA

PPH#10 x 1"#1/4-2010-24#10 x 1"PPHPFHSex NutMachine ScrewPan HeadSelf-drilling ScrewsMachine ScrewFlat Head#25 or 9/64"#7 or 13/64"

NOTE: 750mm MAXIMUM DOOR WIDTH OPENING FOR EUROPE FOR 36" DEVICE 1000mm MAXIMUM DOOR WIDTH OPENING FOR EUROPE FOR 48" DEV

Drill holes.Fasten using lockwashers andscrews provided. Use #7 for 1/4-20machine screw or use #14 self drillingscrews. For sex nuts drill 3/8" h

Mark for 96strikeDrill holes,#7 for 1/4-20 machine screws,and fasten with 1/4-20x1 PPHmachine screws or #14 self drillingscrews. For sex nuts drill 3/

NOTE: BOTTOM BRACKET ISNON-HANDED AND MAY BE USEDFOR RHR AND LHR APPLICATIONSFIG. 7BDrill holes for bottom bolt bracket (see fastenertable)FIG. 7ABott

L2TypeMax Cut-Off36" UnitLength (L)48" Unit6 inPRECAUTIONARY NOTE:NOTE:1. See "EE ELECTRICAL OPTIONS" before reinstalling filler

Caution Required-Special HandlingProcedures for Additional Cut Down Lengthsbeyond edge of cut fillerplate.Reassemble electronicsPlace battery in endca